当前位置:主页 > 常见问题 >

正确使用橡胶接头,提高它性能

作者:上海松夏减震器有限公司 日期:2019-01-22 来源:橡胶接头厂家
   正确使用橡胶接头,提高它性能
   Use rubber connector correctly to improve its performance
   第一:如果在泵出口附近或管道拐角处设计和安装橡胶接头,并将产品用于高压和高层建筑悬挂,则管道必须有固定支架或固定支架。固定支架和固定支架的受力必须大于轴向力,否则产品应安装防拔限位装置。
   First: if rubber joints are designed and installed near the pump outlet or at the pipe corner and the product is used for high pressure and high-rise building suspension, the pipe must have a fixed support or fixed support.The force on the fixed bracket and the fixed bracket must be greater than the axial force, otherwise the product shall be installed with the anti-pulling limit device.
正确使用橡胶接头
   第二:柔性橡胶软接头管结构必须处于自然状态,安装时不要人为地使产品变形。这样可以避免产品的早期损坏和弱化。在安装过程中,严禁使用柔性橡胶接头进行超级位移
   Second: the structure of flexible rubber soft joint pipe must be in a natural state, do not artificially deform the product during installation.This can avoid early damage and weakening of the product.In the process of installation, it is forbidden to use flexible rubber joints for super displacement
橡胶接头的性能
   第三:当柔性胶管接头与管法兰连接时,螺栓线材应延伸到管法兰的一端,以防止螺纹受压时橡胶软接头的拱被挤压或缠绕,两端的螺栓必须对称紧固,以使所有螺栓的紧密性一致,使用条件差。除了增加平垫外,还应增加弹簧垫圈,以防止螺母松动。
   Third: when the flexible rubber hose joint is connected with the pipe flange, the bolt wire shall extend to one end of the pipe flange to prevent the arch of the rubber soft joint from being squeezed or wound when the thread is compressed. The bolts at both ends must be tightened symmetrically to make all the bolts have the same tightness and poor service conditions.In addition to adding flat pads, spring washers should be added to prevent the nut from loosening.
橡胶接头生产制造商
   第四法兰的橡胶接头应安装,使球体加强环的两端全部卡在法兰槽内,以防止球在管道承受压力时拔出法兰。螺栓固定时,拧紧对称螺栓,以确保球于法兰已就位。
   The rubber joint of the fourth flange shall be installed so that both ends of the ball reinforcing ring are all stuck in the flange groove to prevent the ball from pulling out the flange when the pipe is under pressure.When the bolt is fixed, tighten the symmetric bolt to ensure that the ball is in place on the flange.
法兰橡胶接头
 

橡胶接头产品分类

  • 单球体橡胶接头

  • 双球体橡胶接头

  • 同心异径橡胶接头

  • 偏心异径橡胶接头

  • 卡箍橡胶接头

  • 螺纹丝扣橡胶接头

  • 90度橡胶弯头

  • 菱形法兰橡胶接头

  • 橡胶鸭嘴止回阀

  •